[OK] X!},8}~J~
Restricted Rights Legend X!},8}~J~
Use, duplication, or disclosure by the Government is X!},8}~J~
subject to restrictions as set forth in subparagraph X!},8}~J~
(c) of the Commercial Computer Software - Restricted X!},8}~J~
Rights clause at FAR sec. 52.227-19 and subparagraph X!},8}~J~
(c) (1) (ii) of the Rights in Technical Data and Computer X!},8}~J~
Software clause at DFARS sec. 252.227-7013. X!},8}~J~
cisco Systems, Inc. X!},8}~J~
170 West Tasman Drive X!},8}~J~
San Jose, California 95134-1706 X!},8}~J~
Cisco Internetwork Operating System Software X!},8}~J~
IOS (tm) 3600 Software (C3640-I-M), Version 12.1(2)T, RELEASE SOFTWARE (fc1) X!},8}~J~
Copyright (c) 1986-2000 by cisco Systems, Inc. X!},8}~J~
Compiled Tue 16-May-00 12:26 by ccai X!},8}~J~
Image text-base: 0x600088F0, data-base: 0x60924000 X!},8}~J~
cisco 3640 (R4700) processor (revision 0x00) with 24576K/8192K bytes of memory. X!},8}~J~
Processor board ID 25125768 X!},8}~J~
R4700 CPU at 100Mhz, Implementation 33, Rev 1.0 X!},8}~J~
Bridging software. X!},8}~J~
X.25 software, Version 3.0.0. X!},8}~J~
2 FastEthernet/IEEE 802.3 interface(s) X!},8}~J~
1 Serial network interface(s) X!},8}~J~
DRAM configuration is 64 bits wide with parity disabled. X!},8}~J~
125K bytes of non-volatile configuration memory. X!},8}~J~
8192K bytes of processor board System flash (Read/Write) X!},8}~J~
--- System Configuration Dialog --- X!},8}~J~
Would you like to enter the initial configuration dialog? [yes/no]: y X!},8}~J~
您是否进入初始化配置对话,选Y X!},8}~J~
At any point you may enter a question mark '?' for help. X!},8}~J~
Use ctrl-c to abort configuration dialog at any prompt. X!},8}~J~
Default settings are in square brackets '[]'.Basic management setup configures only enough connectivity X!},8}~J~
for management of the system, extended setup will ask you X!},8}~J~
to configure each interface on the system X!},8}~J~
Would you like to enter basic management setup? [yes/no]: n X!},8}~J~
您是否进入基本配置安装,选N X!},8}~J~
First, would you like to see the current interface summary? [yes]: y X!},8}~J~
首先,您是否看一下当前端口状态 X!},8}~J~
Any interface listed with OK? value "NO" does not have a valid configuration X!},8}~J~
Interface IP-Address OK? Method Status Protocol X!},8}~J~
FastEthernet0/0unassigned NO unset up down X!},8}~J~
Serial0/0 unassigned NO unset down down X!},8}~J~
FastEthernet0/1unassigned NO unset up down X!},8}~J~
Configuring global parameters: X!},8}~J~
Enter host name [Router]:RouterA X!},8}~J~
输入路由器的名字 X!},8}~J~
The enable secret is a password used to protect access to X!},8}~J~
privileged EXEC and configuration modes. This password, after X!},8}~J~
entered, becomes encrypted in the configuration. X!},8}~J~
Enter enable secret: aaa X!},8}~J~
输入密文 X!},8}~J~
The enable password is used when you do not specify an X!},8}~J~
enable secret password, with some older software versions, and X!},8}~J~
some boot images. X!},8}~J~
Enter enable password: bbb X!},8}~J~
输入密码(不能和密文相同) X!},8}~J~
The virtual terminal password is used to protect X!},8}~J~
access to the router over a network interface. X!},8}~J~
Enter virtual terminal password: ccc X!},8}~J~
输入虚拟终端的密码(以备远程登录) X!},8}~J~
Configure SNMP Network Management? [yes]: n X!},8}~J~
配置简单网管吗?选N X!},8}~J~
Configure IP? [yes]: y X!},8}~J~
配置IP吗?选Y P c'0.4
Configure IGRP routing? [yes]: n P c'0.4